This is the text version of DirtRider.Net
Click Here for the Full Version

• MX-1000 Chain Lube Question
• 95 YZ250 Rear Wheel Bearings
• Conrod bottom end bearing
• 1/2 throttle help
• inch lbs?
• New rear tire---Need opinions on what to get for my riding conditions
• My YZ125 Sputtering/Reving Problems???
• 1/4 throttle... then nothin' !
• Replacing fly wheel side crank seal
• Bike revs out at start
• lost spark
• Smoking and slipping... what the heck!?!
• need help losing coolant
• Damaged jet removal
• Head milling, cylinder pressure, and race gas
• Mixing Tranny Oils
• Help Cr125 not starting
• bleeding brakes, line full of air.
• xr 70 fork oil capacity
• steering stop repair ideas please
• front sproket play?
• Bad Ignition
• New top end is leaking coolant????
• [CR] Sprocket/Chain help requested
• rear tire question
• valve spring rates
• Swing arm bolt
• compression tester
• Proper 2 stroke compression test?
• TS250 Oil Pump Question
• Pilot jet?
• Coolent leaking?
• Building up from crank bearing swap and got a trans question ?
• Honda Scooter Problems :ride:
• what the heck i got major bike issues
• Kick starter problem
• Spark Plug Problem?
• Quick answer!!
• Cranks seals on IT 490??
• Leaner or Hotter?
• 1984 Honda ATC125M
• Four stroke timing
• Fluid?? Where did ya go??
• got a bit of a prob.
• Installing cam in crf250r "04"
• Big Air Carb
• stiffer suspension
• rear pad probs
• kx250 power loss
• PW50 Oil Injector/Sticky Throttle
• cable ends
• Crankcase Cover and Stator Question.
• Jetting help..
• HELP - EBC Brakes - Semi-metallic or Metallic???
• Broken reed
• Yamaha TT600R ignition dies when wet !
• 98 kx 250
• Deck Height 00 CR 125
• Used YZ 250 Question
• Break in procedure question
• Striped Out Oil Drain Bolt
• Sputter Related
• Parts For Old Bikes
• spokes loose after every ride
• Standard bore or overbore???
• exhaust o rings.....
• RK X-ring rubbing case on 04 KX250
• New Chain
• OIL Filters!
• Stripped locknut on chain adjuster.
• 1999 CR250 won't start
• TTR 90 Carburetor Problem - I Think
• Pipe ??
• Piston Clearances / Ring Gap
• Eric,can you identify who makes this tool
• to much oil?
• Stalls out, need advice...
• aluminum shavings?
• Got my bike back From shop, have some ????
• replacing fork seals?
• New bike, a few questions..
• power valve lock washer
• Any ideas
• 2001 RM 125 piston i.d. #'s
• Rear Shocks Kd125
• YZ 125 -99 head bolt torque ?
• Rebuilt 02 CR125
• Steering Head torque for 01 KX 250?
• 91 CR 250 rear shock question....
• Jetting Anyone?
• HELP! 2002 Kawasaki KLR 650,model C. Needed 5 gal gas tank.
• Just bought a used XR250R
• 83 RM250 Problems with 2nd gear
• Chain Servicing
• Help-Top end rebuild
• Help-Yamaha Customer Service is Useless
• 02' yz250f oil leak
• Can't Get 72 Kawi F6 To Start
• Loose Spokes - Wheel Wobble??
• Removing CR250 2002 Power Valves
• Fuel issues
• 90 Yz 125- Manual Doesn't Show Compression
• Cr250 Rebuild
• 98rm250=96rm250
• How did this happen??
• help
• Replaced front brake line, now no front brakes
• quick question about bleeding forks
• float level settings
• CR 125 suspension
• 250cc 2 stroke engine swap in a 125 Chassis
• wheel true devices
• oil leaking
• 1997 RM250 problem with valves
• New top end?
• Semi or Fully Synthetic4T for XR250RN??
• 83 RM250 Stator Adjustment
• Dyno for cujet
• Athena cylinder kit
• Help with settings -99 yz 125
• all balls racing bearings
• Help!!!!!
• Which one is it?
• 05 RMZ 250 std vs fmf T4 silencer dyno
• weird mid slug
• yz 426 fluids?
• Maintanence Cost - Japaneese vs European
• Just when u though u heard it all
• Reed Question
• Questions on Rebuild techniques
• ttr250 fork seal replacement?
• cr 250 help again !
• Newbie in need with a carb question...HELP!
• kdx220 jets work in a kx100?
• can't start for first time in spring
• Bad questions? Bad bikes?
• mikuni carb jets!!!
• replacing clutch cable
• Swimming with the crf230! Oh *@&#%$!!!!
• Salesman
• Cylinder bolt removal??
• oil in the water and water in the crank case mixing
• 1990 Suzuki RM250 Problems
• overflow lines
• Clutch Adjustment?
• YZ clutch/ tranny problem
• Swapping Powervalve
• RM problems
• Driving me crazy
• Point in the right direction for jetting please
• worn clutch?
• clutch problems
• What's the deal?
• IT400 blues
• Ti 18x1.5 sensor bung
• no spark what now: voltimeter?
• yz 250 rear brake all screwed up
• 1994 yamaha suspension /?
• yz250f neutral problems
• Testing an oil injection pump
• Solder??
• RC valve
• Help
• tranny
• 1988 cr125 won't start
• Slow starting TTR225
• free play?
• How do I torque KX100 sprocket bolts?
• forged piston properties
• CRF will not start
• torque spec on carburetor nut
• Different ratios(piston pics)
• Stock Chain?
• 1990 Cr250
• Cheapest way to bore cylinder???
• crf250x hesitation
• Radiator Flush
• Cant start my XR200!
• Where can I find replacement spokes online
• 1999 CR 250 Bent fork or something?? Need some help
• where do u fill tranny oil
• Little Help? 98 Cr250
• 1998 KX250 any known problems?
• Fork seals:Any Tips or tricks ??
• My first bike, question on jetting, needles on 1st position?
• 04-05 YZ 250 motors
• help blocked radiator
• kx 250 oil leak
• high compression gasket in a cr250
• Coolant loss, bike ran bad during torturous mud race
• CRF250X Mods
• Setting the bead
• torque specs for 1980 kdx 250?
• Hard to remove bolts
• should I restore engine in 89 yz125?
• 00kx125 carb problems
• 96 RM125 Project
• 03 RM250 running rich
• Need Help Bad On Kx 250
• small question

This is the text version of DirtRider.Net
Click Here for the Full Version