Dirt Rider . Net Text Version Home
Pages: 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
- cylinder
- Changing tires
- bone head things
- Rear brake maintenance
- Leaky carb?
- Gas leaking at air screw question
- crank play
- Front Brake Squeal
- '86 kx 125 clutch cover
- broken spoke
- Oil Question for 2S Rebuild and Breakin
- Patch, replace, or slime??
- Is stock jetting rich?
- Triple Clamp Questions
- Engine problems
- Excel Rims
- Carb Tuning
- TPS adjustment
- Oh No! I Got Bad Gas!!
- 2002 yz 1256 mods
- W.E.R. damper oil change???
- portinkg - need a guru
- Using a lapping table
- please help..strange brake problem
- Yamaha knocking..Any expierenced this??
- Hey, Im new to dirtbiking!
- YZ465 top end rebuild
- Identify this Carb !!!
- 2 stroke emissions???? Eric, a question???
- Look at my piston
- Jetting, where to start???
- piston read 02 yz250
- mechanics
- Bad spark plugs
- Hmm I found more power
- Front Brakes
- splitting cases
- yamahabond: will it fix powervalve leak?
- 120/90/19 on a 1.85 rim??
- silencer effect
- Anyone using Motul 50:1
- vertex vs wiseco pro lite
- Ignition timing
- Help - DRZ electrical problem
- Blair & transfers
- KX125 rebuild
- Maintenence
- why?
- Can anyone help? fork seals 1981 YZ?
- Spark Plug
- would boyesen reeds be a good mod for a older bike
- rattle, rattle, klank, rattle
- too much vibration - KX250
- Any frame builders/fabrication shops Charlotte NC
- Brake in
- compression loss, please help
- diagnosing aging motor?
- Installing Circlips
- VP Red VS C12?
- kickstarterwobble on 92 cr125
- getting into mx?
- Advise Needed
- Pontuation for Carbon Tech Low Tension
- any tips on changing tires?
- Reading a piston
- Front brake is super mushy in feel
- Torque or not ?
- Add a bike Carrier !!!!!!!!!
- Silencer?
- Stuck Throttle II
- Which needle to move to?
- Float Question
- Changing Jets
- filter cleaning
- Help with Tire Pressure
- xr80 PLEASEREAD
- yamaha shifter problems
- YZ 465G Jetting Question
- RM125 2000 wont idle
- Clutch problems on RM 125
- I need some info.
- Cleaning inside of 2 stroke pipe
- Is brake bleeding hard?
- Replacement tubes
- spark plug iformation
- odd jetting related question
- What next?
- bike popping out of neutral
- YZ125 Jetting Help
- '96 RM 250 jetting
- Newbie Question: Fresh Topend, Why the idle?
- what the difference
- KX310 performance
- 2001 RM125 Performance...
- Clutch Actuation Arm
- Jetting for KX265 vs KX250: same?
- Porting old Maico's
- '96 RMX 250 head gasket swap w/ RM part?
- 2-ring pistons
- Woodruff key shearing ?!
- loss of power
- frame paint
- 01-cr250 2nd gear missing!
- Flywheel weight installation?
- 2-questions
- CR500?? for Mr. Gorr
- How do you adjust the needle clip
- Jetting Tips
- Cam re-grinds
- reving @ the start
- Tire pressure
- Fork seals on RM
- HELP! Problem with rear brake Piston!!
- pilot jet
- Can I,,,, maybe I should have bought and EXC
- quieter silencer?
- frame paint
- Case matching worth it?
- Piston Crown
- 2002 Kx100 Water Pump Seal
- crank seel leak testing?
- yamaha powervalve stop (i finally did it)
- YZ426 TPS sensor
- Tire Choice
- 99-00 RM rad. shrouds
- Exhaust
- what else should i check on my 82' rm125?
- Just tore apart my engine
- how do you get off old stickers?
- grinding powervalves
- Pipe Cleaning????
- Crank bearings
- Hotter Temperatures while Riding Slow
- what other mods can i get for my rm125?
- Lean Jetting with colder plug-Help
- nickel plating
- Engine noise @ idle
- Premix Ratio for my 250
- Throttle response
- Help: 1993 CR 125 Rear Rim
- OEM Graphics
- Sticker goo removal suggestions.
- OEM vs Wiesco Piston kit?
- almost ready to roll out my 250
- Fouling? Why?
- Fork Oil
- How Often Do You Change Tranny Oil?
- Losing tranny oil
- Worn out seat that has to go...
- How important is fork oil?
- '01 yz426 seized lower rod bearing
- 2002 RM250 suggestions
- Am I Paranoid??
- Dell needs help fast!!
- Trail Tech Speedo
- Reeds vs powerband vs damage
- Clicking Noise
- sprockets
- What's a warmer or colder plug?
- is this bad
- cylinder probs
- Where to buy Clutch kits?
- KX Brake Problem
- Eric's book...yz 250 powervalve
- RM 250 problem
- Brake Rotor Bolt
- Taming the beast, KX250
- Owner's Manual
- KX250 lower end longevity
- 98 rt180 tranny questions??
- Xr200 Carb gone buck
- Engine Idle Problems...
- 80-over?
- Piston Slap
- Any tips on putting on # plate backgrounds?
- after a wot, cld a too lean a pilot cause seizing
- swingarm grease seals
- Oil paradox
- Race gas vs Pump gas
- Scratched Cylinder
- rim lock?
- spokes
- jetting change needed for compression increase?
- Anyone have target squish clearances you swear by?
- Crank Rebuild?
- Pre-mix life
- Race Fuels
- Symptoms of overpacked muffler?
- What happens when you remove the fiberglass?
- Tachometer for regular use on 4 strok
- got a quick jetting question
- jetting kx125 for trails
- Best thing done to bike?
- 1998 CR80 - Running lean but smokes ALOT
- Optimal jetting for maximized performance
- 1982 YZ 250 powervalve
- clunking after rebuild
- torque specs
- 4 stroke max compression ratio
- Cleaning oxidized rear wheel - How ?
Text Version Home
vBulletin Copyright ©2000 - 2009,
Jelsoft Enterprises Limited.
vB Easy Archive Final ©2000 - 2009
- Created by Stefan "Xenon" Kaeser
