Another pre-mix question for CR500's

PsychoCR500 · Jan 10, 2002

I have been using HP2 at 32:1 in my past 3 500's. Now I want to try the Mobil MX4T in my new one so I am wondering is 40:1 better with this oil or should I stay at 32:1. And just to confirm....40:1 would be 1 pint to 5 gallons correct? And, will I need to make big changes to the jetting if I go that route?

KXrider12 · Jan 10, 2002

I don't know a hole lot on 500's but you could get a ratio rite and it tells you all teh ratios form 2 gallons to like 4 gallons of gas

DougMXer · Jan 10, 2002

BelRay MC-1 at 50:1 and you'll be smoking like a baby.
32:1 is too much oil and the bike ends up running richer - since it is not getting as much air as a leaner mix per cycle.

Vic · Jan 10, 2002

Originally posted by DougMXer
BelRay MC-1 at 50:1 and you'll be smoking like a baby.
32:1 is too much oil and the bike ends up running richer - since it is not getting as much air as a leaner mix per cycle.

:mad: :silly:

MikeT · Jan 10, 2002

Originally posted by PsychoCR500
I have been using HP2 at 32:1 in my past 3 500's. Now I want to try the Mobil MX4T in my new one so I am wondering is 40:1 better with this oil or should I stay at 32:1.

If your bike is jetted correctly 32:1 will be fine. I think 40:1 on a bike is too little oil. If you are having a spooge problem I would use Maxima SuperM it has a lower flash point than most oils and will burn more completely.

Originally posted by PsychoCR500
And just to confirm....40:1 would be 1 pint to 5 gallons correct?

Yep 5 gallons = 640 oz.
1 pint = 16 oz.
640/16 =40 so it's 40:1

Originally posted by PsychoCR500
And just to confirm....40:1 would be 1 pint to 5 gallons correct? And, will I need to make big changes to the jetting if I go that route?

Probably, but why make jetting changes to make your bike run well with less oil? If you run less oil, you will have more wear. If your bike will run correctly on 32:1 you will have more oil (better compression) and more protection.....
Take your pick.

MikeT · Jan 10, 2002

Originally posted by DougMXer
BelRay MC-1 at 50:1 and you'll be smoking like a baby.
32:1 is too much oil and the bike ends up running richer - since it is not getting as much air as a leaner mix per cycle.

Not correct Doug:mad:

DanS · Jan 10, 2002

Yes, 1 pint to 5 gallons is 40-1. I run 40-1 in my '87 CR500. I changed the jetting to a 172 main, 55 slow, and 1369 needle. It's spot on. It has a lot of years on it and still runs strong. I've never had any premature wear of the piston or bearings with very little spooge. If you add more oil you will lean your air fuel mixture. If you go with less oil it makes it richer so you may have to lean the jetting some. I've been using Yamlube 2R for a while now and don't get near the carbon deposits I used to.

PsychoCR500 · Jan 10, 2002

Thanks!

DanS- that's EXACTLY what I needed to know!

Another pre-mix question for CR500's

PsychoCR500

KXrider12

Sponsoring Member

DougMXer

Vic

***** freak.

MikeT

MikeT

DanS

Sponsoring Member

PsychoCR500

Similar Topics

Another pre-mix question for CR500's

Sponsoring Member

***** freak.

Sponsoring Member

Similar Topics

Privacy & Transparency

Privacy & Transparency